Play Video

Aquinity² P35 / P70 Ultra Pure Water System

Produces Pure Water and Ultra Pure Water

TESTIMONIALS

Alexandra LorenzTissUse GmbH, Germany
Read More
"Highly satisfied with the Aquinity which has been in our laboratories since 2016 and has been easy to use. The water quality of type 1 and type 2 water is permanently excellent. The service is fast and competent."
Alexandra RindermannASKA Biotech GmbH
Read More
"The Aquinity2 20 P70 analytical is ideally suited for all of our applications, the water quality is consistently excellent. The device works reliably and the service is very friendly, competent and helpful. We have made a good choice with this device."
Vladislav Stroganov Friedrich-Schiller University Jena
Read More
"We have this device in our laboratory since 2016 and are satisfied with its performance. It does what it is supposed to - it produces ultra pure water which can be used in applications sensitive to the lowest concentration of contaminates. The tap water in our location contains high amounts of iron but this water purification system does an excellent job in removing it. The customer support is fast and helpful. We usually receive a reply within 24 hours."
Previous
Next

OVERVIEW

Designed for the production of pure water and ultra pure water out of tap water

  • Aquinity² P versions produce deionised water (< 1 µS/cm/ > 1 MOhm x cm) by reverse osmosis and conditioning module in to the external reservoir (35 liter or 70 liter). 
  • The water can be tapped directly (e.g. for glassware cleaning by hand) or connecting the tank to a laboratory dishwasher. 
  • Out of the storage tank the ultra pure water is produced and then can be tapped with a flexible dispenser. 
  • The Aquinity² water purification system is available in different configurations (Reagent, Analytical & LifeScience) to meet the specific requirements of ultra pure water for different applications. 
  • Analytical is a version with UV lamp for low TOC value. Life Science version comes with UV lamp and Ultrafiltration Module for low TOC and low endotoxin values. 
  • An optional integrated TOC sensor allows the user to monitor the TOC content permanentely online. 
  • Besides that the Aquinity² can be configured as bench top or bench-integrated system with external panel and wall mounted (with inclined display). 
  • The tank can be installed at the side or above the system or even underneath the bench. 
  • Upon request the tanks can be connected in series to reach a bigger volume of reservoir.

Main technical specifications of the system​

Flowchart

The scheme shows an Aquinity P35/70 Life Science with integrated TOC-monitoring.

Flowchart: Aquinity² P35 / 70
Options Bench mount Aquinity

Bench integrated configuration (BI version)

To save valuable benchtop space the system can be ordered as BI configuration. The system will be installed underneath the work bench and only the display and dispenser are mounted on the wall.

Options: Wall mount Aquinity

Wall mounted configuration

To save valuable benchtop space the system can be ordered as wall mounted configuration. the whole system can be mounted on the wall with inclined display.

Options: External pump Aquinity E35 / 70

External pump

Compact pump is required when feeding laboratory equipment such as autoclaves or laboratory dish washers.

Options: TOC Monitoring Aquinity P35

TOC-Monitoring (TI version)

The TOC monitoring during production and intermittent measurements during non-use periods allows to check the organic content in water continuously. The TOC value is measured between 1 and 999 ppb and can be shown in the display to monitor organic impurities.

Options: Volumetric Dispenser

Volumetric dispensing

Our dispenser allows the volumetric controlled dispensing of water with an increment of 0.1 L and a tap volume from 0.1 to 99 L. The system prevents overflow of containers and allows to dispense water without supervising.

Options: IQQ Documents Aquinity P10

IQ/OQ documents

Validation documents for water purification systems.

Options: memTap Aquinity P10

memTap

To be integrated into an ultra pure water system with a max, flow rate of 2 L/min. Point of use dispense arm with integrated control unit. Two joint to move it horizontally and vertically allowing to fill containers up to 55 cm height. Volumetric dosing of ultra pure water allows filling of containers without the attention of user, dosing eange 0.1 – 99 L, variable input and storage of values, after volume has been dispensed system goes back to standby.

Technical Specifications
pure water + ultrapure water quality< 2 µS/cm; Type II + 0.055 µS/cm; Type I
resistivity> 0.5 MegaOhm; Type II + 18.2 MegaOhm/cm; Type I
total organic carbon (TOC)< 10 ppb Reagent, < 5 ppb Life Science, < 3 ppb Analytical
dispensing flow rate2.0 L/min (1.5 L/min Life Science)
production rate10 L/h, optionally 20 L/h
bacteria< 1 cfu/mL
particulate> 0.2 µm less than 1 particulate/mL
pyrogen (endotoxins)< 0.001 EU/mL*
RNAse< 1 pg/mL*
DNAse< 5 pg/mL*
dimensions, weight, power504 x 680 x 535 mm, 16-20 kg, 110 - 230 V
*Life Science
Feed Water Requirements
type of feed watertap water
feed water conductivity< 1400 µS/cm
inlet pressure1.5 to 6 bar
free chlorine< 0.1 mg/L
Silt Density Inded (SDI)< 3
pH3 to 9
temperature5 to 25 °C

FAQ

The "Aquinity² P35/70" is a laboratory water system that provides its user with ultrapure water for a wide variety of applications in the field of analytics and laboratory applications. The designations "35" and "70" stand for an external tank with a capacity of 35 and 70 liters respectively.

The Aquinity² P35/70 systems produce pure and ultrapure water from drinking water. This makes the Aquinity² P35/70 the ideal system for a laboratory that pursues different types of applications that also have different requirements for the purity content of the laboratory water.

The compact design of the Aquinity²35/70 takes up little valuable laboratory space and its simple and intuitive operation makes it easy to integrate into everyday laboratory work.

Customers have the option of selecting a system with or UV lamp, depending on the area of application. If work is carried out in the life science sector, we also offer a configuration with ultrafiltration module. This eliminates the need for frequent changes of biological final filters and reduces investment costs.

Due to the simple and clear design of the software, the user can quickly operate the device through intuitive handling. The software informs the user when limit values have been exceeded or when consumables such as cartridges or UV lamps need to be replaced. A wizard guides the user through the individual steps.

In addition to the hoses for inlet and outlet, the scope of delivery also includes an adapter that makes it easy for them to connect the system to a drinking water connection.

Depending on the configuration, the system has a 35 or 70 liter tank as standard. Should a higher capacity be required, several tanks can also be connected in series.

By using an external tank, Type II water can be tapped through a separate tap. The tank also has a rear outlet so that external systems such as analyzers can be fed directly. A booster pump can also be offered on request to pump the water.

The installation location can be designed very flexibly. Depending on the available work surface, the system can be integrated directly on the equipment, on the wall or under the lab bench. The display, which can be installed flexibly, also ensures convenient operation.

Complete your name and email to receive the application note.

Analysis of the amino acid composition of cell culture media
Get download link